Welcome to Control.com, the global online community of automation professionals.
Control.com - Nerds in Control
Member Login
Search
Jump to a Date
Sponsored Communities
Cool stuff
Twitter Feed
Neat Stuff
Visit our shop for nerds in control lifestyle products.
Thermal Overload
The threads that wouldn't die...
- PC reliability?
- Windows, real time
- PID loops
- PCs vs. PLCs
- Replacing people
- MS 'monopoly'?
- Software quality
- Where do we go from here?
- Why pay?
- PC reliability?
- Windows, real time
- PID loops
- PCs vs. PLCs
- Replacing people
- MS 'monopoly'?
- Software quality
- Where do we go from here?
- Why pay?
Fortune
Artistic ventures highlighted. Rob a museum.
RSS Feed
Use this link to get an RSS feed of the Control.com article flow, for private, non-commercial use only:www.control.com/rss/
To get a personalized feed, become a member at no cost.
1
Control.com member...
Member Information and Posts by Robert_WillisCompany: Schneider Electric
IT guy thrown into PLC world. Backing up PLC configuration.
New Replies:
Billy:
If you want to contact me directly please send a e-mail to robert.willis [at]...
You can connect to a Modicon Quantum Controller via the following methods.
1. Direct RS232...
Utilizing the Concept Software connect to each controller and confirm that you can connect with a...
Can MicroLogic PLC read Modbus Holding Registers in the 5xxxx range?
New Replies:
The typical Modbus Address Scheme is :
0x = Digital Outputs (Bit)(Read / Write)
1x = Digital...
How to read weight from IND 780 using Modbus TCP/IP
New Replies:
I do not have PL7 installed on my computer and am going from memory.
You do not enter 400001...
It would help if you provide us with the details of which programming software you are using (PL7...
from the Forum department...
AB Micrologix 1100 Modbus Communication with Telemecanique Motor Startertrying to communicate an AB ML1100 with a Telemecanique motor starter unit with a modbus communication module
New Replies:
The Sycon software is not required since the TeSysU is using a Modbus connection. Contact your...
Connecting a rs485 4-wire to 232 converter. Third party device is 4-wire and my device is a 2-wire
New Replies:
You need to purchase a RS485 4-Wire to RS232 converter. Depending on your computer requirements you...
Transfer problem since change in program
New Replies:
In Unity Pro you must turn on the feature that allows you to upload the program from the...
Your messge is very hard to understand so I am going to repeat it so that I can meake sure that I...
A problem with not seeing when a yaw gear fails causing the turbine to be yawed by just one yaw motor instead of 2. We want to get some kind of component for monitoring baseload current for pitch motors and trippng on overload.
New Replies:
Take a look at the Schneider Electric TeSysT Motor Overload Relay. It is available with numerous...
The HMI does record or register any numerical inputs. What can be the cause.
New Replies:
Please check your part number for the PLC. The part number that you have provided appears to be a...
XBTGT2110 and a TWDLCAA24DRF CPU that does not want to communicate
New Replies:
The two most common causes for this are the use of a incorrect cable or the serial port...
1
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2009 Nerds in Control, LLC. All rights reserved.
Our Advertisers
Help keep our servers running...
Patronize our advertisers!
Patronize our advertisers!