Select Page: 1
Control.com member...
Member Information and Posts by controman
User Picture
Topic: Power generation equipment control.
from the Forum department...
REC316*4 ABB relay Problem
Posted by Controman on 31 May, 2013 - 10:39 am
Unknowen Message showen by the relay
Topic: Power generation equipment control.
from the Problem with REC 316*4 department...
REC316*4 ABB relay
Posted by Controman on 25 May, 2013 - 9:50 am
Problem with the message: "-System Restart- Are you sure?
NO yes
Originally posted by Umar on 4 September, 2011 - 5:20 am
When we try to put the machine to turning we get the following trip "Starting means turbine shaft fail to break turbine away"
New Replies:
Umar and KP, Is there in your gas turbine what we call lift oil pumps for generator shaft...
Originally posted by Controman on 25 February, 2013 - 5:48 pm
What specificity does R controller have with the DC LED?
New Replies:
Thank you GETech for the added information. And thanks to CSA for the correction. Best regards...
Of course all these informations help and make us aware of problems to avoid. So thank you...
Thank you CSA for your explanation There was no information in GE documentation (in our site)...
Topic: Power generation equipment control.
from the Forum department...
Toshiba power transformer cooling system
Posted by Controman on 23 February, 2013 - 6:03 pm
What's the role of the oil flow indicator?
Originally posted by controman on 6 January, 2012 - 4:20 am
Can a reversal power affect the rotor of a generator?
New Replies:
Mr Phil Corso, Thanks for your reply to my thread I'm sorry for my not deliberated late...
Topic: Power generation equipment control.
from the Forum department...
9001E GT Trip by loss of flame
Originally posted by controman on 23 December, 2011 - 12:45 am
Gas turbine tripped by loss of flame
New Replies:
Thank you for replying to this thread: Dear Mr G.Rajesh, thank you for the information about...
Topic: Human-Machine Interface and SCADA.
from the Forum department...
CIMPLICITY units system
Originally posted by baskar on 11 February, 2011 - 9:59 am
Convert of units in HMI?
New Replies:
-"309Eguy" and "CSA", I followed the procedure but with the addition added by...
Well, I have access only to another computer witch has not the problem, but has possibility to...
Hi! Otised! So what to do to convert unities in all (Toolbox, historian and all) Process...
Thank you for your reply 309Eguy. ...
Originally posted by Controm on 7 November, 2010 - 4:19 am
Ground fault alarm after flame appearing
New Replies:
Thank you again CSA for your replies, recently we found the problem in the clutch 20CF (even if we...
Topic: Power generation equipment control.
from the Forum department...
Trip by high pressure of exhaust conduit
Posted by Controman on 11 February, 2011 - 10:45 am
Alarm by L63ETH in GE gas turbine.
Topic: PLCs and related questions.
from the Forum department...
role of some registers
Posted by controm on 20 September, 2009 - 7:26 pm
why "MOV D100Z0 D101?"
Select Page: 1
 
 

Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2014 Nerds in Control, LLC. All rights reserved.

Users of this site are benefiting from open source technologies, including PHP, MySQL and Apache. Be happy.


Fortune
This fortune intentionally not included.
Advertise here
Advertisement
our advertisers
Help keep our servers running...
Patronize our advertisers!
Visit our Post Archive