Control.com - Nerds in Control
Error value when calibrating pressure transmitter
how P&F make isolator for transmitter connects
New Replies:
thank u david. our problem solve bcoz indicator need 1-5 V our transmitter o/p 4-20 mA. Connect a...
replacing pneumatic transmitter with electronic transmitter
orifice plate flow differs from vendor's data sheet
New Replies:
How we get P&T calculation for accurate reading in orifice plate.
...
have to measure boiler drum level of 500 mm
New Replies:
Our transmitter is 3000 series of honeywell make. n model no: STD-120-E1A.
distance from two leg...
Fuel Air ration for gas fired burner
using pneumatic air for pressure test
hi
What is the basic criteria for selection of Flow meter?
Solution for display and alarm technology to monitor temperature.
New Replies:
thanks kt,
WE do not require analog output. We need only contact type alarm output. Actually we...
dear kt,
thanks for your reply. can you tell me how can we configure as per my requirement....
from the instrumentation department...
One HART Communicator to communicate with different manufacturers terminalpurchase only one manufacture HART terminal for configure different manufacturers' transmitter
Where are Globe and Butterfly control valves generally used
Change fields from instrumentation to design engineer
axial vibration is increasing gradually...
Engineering Standards of Field Instruments in Petrochemical Plant
Need a portable type flow meter
need PLC with a few inputs and outputs
Smart pressure transmitter with HART protocol
suitable distance for installing presseure transmitter
New Replies:
thank u sir. Can we install pressure transmitter before control valve? What is the advantage and...
difference between Pressure and Flow control valve
Ignition Torch
Boiler Three Element with US1000 Yokogawa
New Replies:
thanks ben,
sorry, steam flow signal and drum level signal goes to input of the level controller...
Versa Max PLC of GE Fanuc to connect with our CS3000 DCS?
New Replies:
Do you mean for Modbus protocol or like that? Sorry, how we can confirm this?...
Air Flow Measurement in Control Valve
Air flow decrease in 10" line pipe
New Replies:
Thank u NG. We think there may be leakage some where. But line has -ve pressure line. For that we...
We have orifice plates in natural gas line, process natural gas line and methanol line. It has been...
It is in 20% difference, orifice plates are installed correctly. Earlier it had shown accurate...
How can we measure Interface level measurement?
New Replies:
How we take high and low pressure impulse line? How do we calibrate the DP with respect to Level?...
Thank u roy. I need this for academic purpose. What is other method? Is there any DP type...
>Are you talking about interface detection or interface level detection? The first refers to...
Sorry, it is petrol and diesel. How do we calculate this level in DP type methol?...
Thanks for your reply. It is liquid level, is water and methanol....
It is methanol and water....
How we should maintain good instrumentation standards practice...
New Replies:
Thank u abhijit. Generally in india how [does] industry follow this? Can u give some idea....
Safety Relief Valve pressure
How do four Local Node Units communicate with Field Control Unit through ESB Bus Coupler In Centum CS 3000 Yokogawa DCS?
New Replies:
Thanks for your reply. Our Controller Model No is AFV10D and Node Interface Unit Model No is ANB10D....
What is the fieldbus device?
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2013 Nerds in Control, LLC. All rights reserved.
Users of this site are benefiting from open source technologies, including PHP, MySQL and Apache. Be happy.
Fortune
I have yet to see any problem, however complicated, which, when looked
at in the right way, did not become still more complicated.
-- Poul Anderson
