Recent content by Chemsouhd

Good afternoon Jakky, Well, long time no see ToolboxST, I'm trying just to help, tell me please: You've changed one LVDT? you didn't tell us if calibration were done or not?. Also, did you checked Vrms (7 Vrms) feeding of LVDT with fluctuation? Please check wires in PSVO terminals be sure that...

Hello, First, try with an online ground fault detector, not very useful as many inputs has the same common wire... Secondly, you can simply by using Alarms viewer utility of GE, you can see exactly what happen at 3300rpm. If all the time the ground appears exactly at 3300rpm level of...

Hi, For your information: this is not about the DONGLE (dongle is a hardware license to open the app after installation). Instead you can see on your toolbox DVD package supported OS. If windows 8 is not supported by your version, I'm afraid to tell you that you cannot install it on that...

Hello, Try with https://paktechpoint.com or even https://www.instrumentationtoolbox.com are pretty similar. For me as a turbine control engineer I found a lot of things... Hope this helps. Good luck.

Hi Ivgman, You didnt describe the problem!!! I'll try to respond as I have understand (if the probleme is equality otherwise please tell us your probleme: Looks like you have changed version A to B. Simply point on the card from hardware tab, right click and then modify and select...

Hi iqbal5903, You're right, I remember, I had almost the same probleme with UCSA Mkvie controller. (tell us please which one do you have? I suppose its UCSA since you're talking about flashing Led code). However, keep in mind that with TMR application, and with just one controller you...

Dear Demigrog2, I think you mis-understanding. the originally issue, please refer the original post. as I mentionned before this is not a problem of CF. as I said before, I took off the CF of the older Controller I inserted it on a new one. it worked fine, without any setup of IP or...

Unfortunately not yet, I'm always working on the issue. One of GE documents says the following: "Two micro-miniature 9-pin D connectors: COM1: Reserved for diagnostics, 9600 bauds, 8 data bits, no parity, 1 stop bits. COM2: Not in use. For cabling use one the following: 1/ Standard...

Thanks guys, However temporary I prepared another controller (spare). I used the older Flash Card taken off from the older faulty controller, now its okey, with new controller. The unit is again online. However, since I'm convinced that the older controller is not hardware damaged, now...

Hello everyone, I do agree with Mr CSA in his theory. Since we have almost the same machine 9FB, with DLN 2,6+, MKVIE, I'll try to answer the question at the first topic. Well I tried to tune on the IBH: Actually It works on two principal modes: 1/ Extended DLN Turndown: as its name...

Dear andstennett, Well well, I wanna share my experience with the issue: 1/ Unit online: not too much to do, you can try to reboot it manually once, twice... Til 5 or 6 times it could work...otherwise You can also (with controller state OFF) try to remove flash card memory, wait awhile...

Hi, did you tried to upgrade BIOS software, in general new upgrades bring new features, maybe new version recognize larger HDD. I know its not so easy to find an absolut's upgrade!!! just try it who knows. Good luck.

Dear iqbal5903, <b>Moderator's Note:</b> the paragraphs below were written without any punctuation. I put some periods and commas in where I hope they made sentences with logical sense. You need to configure each port and trunk port each one a part and which VLAN it belongs from port 1 to...

Dear Wahid, In fact control system is trying to control SRV downstream gas pressure FPG2 or P2 (upstream pressure of the GCV) by moving SRV, not just controlling the valve. In order to get closer to the FPGR (P2 setpoint) which is a function of TNH (Turbine speed). FPGR is lower at low...