Latest Oil & Gas Technical Articles

Categories

An Introduction to Air Quality Measurement and Sensors

This article introduces the role of air quality measurement in factories and manufacturing facilities. It also covers the different sensors available for air quality measurement systems.

January 13, 2021 by Muhammad Asim Niazi

Using Measurement While Drilling and Logging While Drilling in Automation

This article discusses measurement while drilling (MWD) and logging while drilling (LWD). Both techniques increase the efficiency and capability of directional drilling as well as the safety of the operators.

December 20, 2020 by Anish Devasia

Wearable Technology in Industrial Manufacturing

As electronics become smaller and more energy-efficient, wearables are getting more attention in manufacturing. Learn about some of the research involved in developing these wearables.

December 02, 2020 by Jeff Kerns

Understanding Boiler Safety Controls

This article looks at the safety systems included in boilers to alert malfunctions and prevent damage when issues arise. Learn about the safety systems and the ISO standard used to keep boilers running smoothly.

November 18, 2020 by Muhammad Asim Niazi

Proper Maintenance of a Boiler System

This article explains the importance of developing a maintenance schedule for boiler systems and the different parts of the systems that need to be included in the maintenance plan.

November 10, 2020 by Muhammad Asim Niazi

What is the BACnet Protocol?

Building Automation and Control Network (BACnet) is commonly used in building automation systems. Learn how BACnet works and the different network technologies used to set up the system.

November 02, 2020 by Muhammad Asim Niazi

Introduction to Distributed Control Systems

Distributed control systems (DCS) evolved out of control systems for facilities, but their scope can be difficult to fully understand. This article explores the role of a DCS and how it fits in with PLCs and PACs.

October 31, 2020 by David Peterson

The Function and Parts of a Building Automation System

Building automation systems (BAS) control the environmental parameters of a factory. In this article, learn about the requirements and components of a BAS.

October 25, 2020 by Muhammad Asim Niazi

ISO 9001 & Calibration Explained

Learn about the importance of the ISO 9001 standard and some essential procedures and considerations to make when using the standard.

October 23, 2020 by Muhammad Asim Niazi

The Difference Between Variable Frequency Drives (VFDs) and Soft Starters

The following will examine how to reduce the wear on motors during startup and compare soft starters and variable frequency drives (VFDs). 

October 17, 2020 by Jeff Kerns

Measurement Tools for Mechanical Maintenance

This article explores what tools can be used to predict and prevent costly mechanical breakdown events occurring from heat, vibration, or humidity.

October 13, 2020 by David Peterson

How to Regulate Pressure in Fluid Systems

Regulating the pressure in a fluid system is the purpose of the appropriately-named pressure regulator. In this article, learn more about pressure regulators.

October 09, 2020 by David Peterson

Understanding Different IP Enclosure Ratings

This article will provide an overview of the IEC (International Electrotechnical Commission) IP (Ingress Protection) ratings, IEC standard 60529, sometimes referred to as International Protection code.

September 16, 2020 by Dennis Lynch

Orifice Plate Sizing for Flow Measurements

Learn about orifice plates and specifically how to size orifice plates for flow measurements and the different flow rates associated with them.

September 11, 2020 by David Peterson

How to Successfully Perform Root Cause Analysis

This article discusses the direct and indirect causes of Root Cause Analysis (RCA) and some effective solutions one can use to properly define RCA.

September 01, 2020 by Muhammad Asim Niazi

Root Cause Analysis in Manufacturing: How Does it Work?

Root cause analysis (RCA) is a method used to identify the root of specific problems. Below are the steps necessary to complete RCA.

August 31, 2020 by Muhammad Asim Niazi

Different Techniques for Condition Monitoring

Condition monitoring focuses on the physical parameters like temperature and vibration, rather than the product parameters.

August 29, 2020 by Muhammad Asim Niazi

Motion Control Systems: Velocity and Acceleration Feedforward

Learn the strategy called feedforward which can predict motion control system outputs. This helps to turn the feedback into a double-check as opposed to the sole provider of the output signal.

August 14, 2020 by David Peterson

How to Troubleshoot Resolvers

Learn about the electrical characteristics of resolvers and how to properly conduct different troubleshooting tests to ensure they run at their highest performance.

July 14, 2020 by Anish Devasia

Understanding Thermal and Pressure Safety Valves

Safety is a concern within any sort of system containing potential energy, whether electrical, chemical, gravitational, or fluid. Each of these has special methods of protection, and for the fluid systems, certain safety valves are used in situations when excess pressure can be a problem.

July 11, 2020 by David Peterson