Select Page: 1
Control.com member...
Member Information and Posts by cheers73
Topic: Continuous process industries, DCS questions.
from the Forum department...
Defining a critical instrument
Posted by cheers73 on 16 April, 2013 - 11:51 pm
Is there a standard methodology to identify critical instruments?
Topic: Sensor technologies.
from the Forum department...
Bearing Temperatures
Originally posted by Owais on 5 March, 2013 - 2:21 am
Bearing Temperatures hunting
New Replies:
There may be various reasons. Some of them are listed below 1. Improper grounding of system: The...
Topic: Sensor technologies.
from the Instrumentation department...
Flange type DP Transmitter zero error
Originally posted by Ravindra on 17 March, 2013 - 1:10 am
Flange type DP Transmitter zero error
New Replies:
Dear Ravindra, Have you checked zero of the transmitter before taking it in line coz? if we...
Topic: Continuous process industries, DCS questions.
from the automation department...
Drum level control by two element
Originally posted by atish on 11 March, 2013 - 4:53 am
What is cascade control & explain two element in simple language?
New Replies:
In case of drum level control a. Single element control - Drum Level as input' b. Two element...
Topic: Human-Machine Interface and SCADA.
from the Instrumentation department...
3500/93 BNIL system display hanged
Posted by rishi on 18 May, 2012 - 2:34 am
3500/93 system display for 3500 BNIL system is hanged up
Originally posted by parinya_naraj on 9 May, 2012 - 2:31 am
Are there technical concerns if I connect 2 temperature transmitters with 1 thermocouple?
New Replies:
Either use dual thermo couples which in most probability are nothing but two T/C extension wires...
Topic: Power generation equipment control.
from the Mech.E department...
boiler feed pump scoop control
Originally posted by Naji on 9 May, 2012 - 8:25 am
What is scoop control for boiler feed pumps?
New Replies:
Scoop controller is a hydraulic device (which i have seen in my FD fans) which regulates the FD fan...
Topic: Sensor technologies.
from the Instrumentation department...
analog 4-20mA output transmision
Originally posted by Kiyani on 10 May, 2012 - 6:02 pm
Analyzers analog output signal 4-20mA transmission
New Replies:
As this is analyzer, your case comes under the passive loop where in instrument itself provides...
Topic: Engineering and workplace issues.
from the Forum department...
Pneumatic Isolation procedures
Originally posted by DAGaj on 11 May, 2012 - 11:19 am
Isolation of a 6mm airline in the field
New Replies:
The very first question which comes to my mind is whats the use of NRV? is there any other system...
Topic: Continuous process industries, DCS questions.
from the Automation List department...
Control valve positioner
Originally posted by Hemanth on 8 March, 2007 - 10:56 pm
I would like to know the operation of positioner.
New Replies:
You must calibrate the I/P converter so that there is 1 to 1 relationship between input and output....
Topic: Application Questions and Problems
from the Automation List department...
4-20ma and loop powered
Originally posted by Pchan on 3 April, 2008 - 11:37 pm
4-20ma and loop powered
New Replies:
> why we have to use 4 wire connection we can measure with 2 wire itself......... There...
Topic: PLCs and related questions.
from the Clarification Required department...
Advantages and Disadvantages of QMR PLC Over TMR PLC
Posted by Rishi on 10 May, 2012 - 5:10 am
What advantages and disadvantages have QMR PLC over TMR PLC?
Topic: Sensor technologies.
from the Automation department...
Pressure measurement at a very high Temperature
Originally posted by sushant on 27 April, 2009 - 7:18 am
Process Temperature is 1500 Deg Cen & process pressure is 2 Bar abs max
New Replies:
Can we go in for alternate method like measuring back pressure of an inert fluid. Say instead of...
Topic: PLCs and related questions.
from the Automation List department...
Advantages, Disadvantages of PLC over DCS.
Originally posted by Kumar on 17 February, 2002 - 12:41 pm
What are the advantages & disadvantages of a PLC over DCS...
New Replies:
> What are the advantages & disadvantages of a PLC over DCS? Basically PLC comes into...
Topic: Sensor technologies.
from the Forum department...
motor speed on pc
Originally posted by sukhi sagoo on 9 June, 2010 - 5:19 pm
need to show motor rpm on pc.
New Replies:
sukhi, Just tell me if there is any speed measuring device installed on your motor or not?...
Posted by Sandeep Rishi on 10 June, 2010 - 1:31 am
From where can i get the operation and maintenance manuals for MSG3000.
Topic: Sensor technologies.
from the Very Strange department...
Temperature increase when it rains (Thermocouple)
Originally posted by J.C Bay on 27 April, 2010 - 4:08 am
Temperature increase when it rains.
New Replies:
Just check the compensation cable connection throughout the circuit. Connections may be reversed at...
Posted by Sandeep Rishi on 28 April, 2009 - 12:07 am
How to remove parial choking in the naphtha flow measuring impulse line?
Topic: Sensor technologies.
from the Instrumentation department...
Solid Level Measurement
Posted by Rishi on 28 January, 2009 - 12:04 am
Catalyst level measurement in catalyst hopper
Topic: Power generation equipment control.
from the Process Instrumentation department...
Control Philosophy
Originally posted by CUDC on 22 January, 2009 - 8:39 am
Can someone guides me to find the general control philosophy of Balance of Plant?
New Replies:
Sir, In cae of power plant..balance of plant (BOP) consists of everything except that of Boilers,...
Select Page: 1
 
 

Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2013 Nerds in Control, LLC. All rights reserved.

Users of this site are benefiting from open source technologies, including PHP, MySQL and Apache. Be happy.


Fortune
Ask not for whom the telephone bell tolls ... if thou art in the
bathtub, it tolls for thee.
Advertise here
Advertisement
our advertisers
Help keep our servers running...
Patronize our advertisers!
Visit our Post Archive