Select Page: 1
Control.com member...Member Information and Posts by lolai
from the bently nevada yokogawa interface department...Bently Nevada output to Yokogawa
Bently Nevada 3300/55 VMS card to Yokogawa AI card not working
Dear Muhammad Nizam It looks some setting issue at card. try to have close look at other inputs...
from the Instrumentation department...Communicator ABB AMD 230 Absolute pressure TX.
Communicator ABB AMD 230 Absolute pressure TX.
Thanks Mr. CSA, Anonymous and David I appreciate your efforts to make this confusion clear to...
thanx David i have tried to fix the issue using screw driver but could not succeed because i...
from the Forum department...frequency bias setting of combined cycle plants
to analyse the response of combined cycle plants operating on frequency influence
if we take reference of Siemens V-94.2 with ABB steam turbine gain and frequency of individual unit...
from the Forum department...Gas turbine compressor output
pressure output from gas turbine compressor
Gas Turbine Siemens V 94.2 has one pressure transmitter (MBA21CP001) at compressor discharge which...
from the Instrumentation department...GT compressor inlet pressure
which factors effect the reading of compressor inlet pressure
Dear CSA I will test the reading as per your advise and share the result. P&ID shows...
from the automation department...Digital Watt Indicator
Digital Watt indicator
from the Forum department...foxboro dcs - Looking for a tutorial
Looking for Foxboro DCS tutorial
dear khaled it is good to hear that you have the good IT background but for EWS you should have...
from the Instrumentation department...IGV Hunting
GT in partial TETC mode and IGV Hunting
Infi-90 is the control system at our plant...while this issue was fixed automatically when we...
Dear CSA i will follow your instruction during troubleshooting.. yes your are right TETC in GT...
> from few days we have observed hunting in IGV, machine remain about 95% on TETC > but some...
from the Instrumentation department...Replacing Differential Expansion Probe
At which Rotor temperature should differential expansion sensor be replaced?
Dear CSA, Thanx for your contribution. i appreciate your advice. when we shutdown the unit...
Dear friends, OEM says it should be done on ambient temperature but i think if it requires only...
from the Instrumentation department...Biffi Gas inlet shuttoff valve
Dual source pneumatic and hydraulic actuator operating procedure
from the Energy Management department...OSI PI Client installation Problem
I can not install OSI PI Client on system with win 7
from the instrumentation department...I/P positioner and I/p transducer Control valve
Difference between I/P positioner and I/p transducer
Transducer doing only conversion like I/P transducer or mostly called Convertor. I/P stands for...
from the Instrumentation & Control department...GT Manual Trip
GT V94.2 manual (panel) trip
from the mechanical department...HRSG
What does the term Lay Up mean when referring to protecting HRGS from corrosion during main outages
>Draining of water depends on duration of Layup. www.babcockpower.com/pdf/vpi-03.pdf this...
from the Instrumentation & Control department...PCU went offline due to IMASO01
Suddenly all the Cards of Infi90 Process control unit(PCU) turned in error mode staus LED Red.
from the Instrumentation department...BAILEY INFI-90 ETIMER CODE 86
ETIMER (Function code 86)Shows 26 hour increments in 24 hours.
from the Instrumentation and Control department...DCS Infi-90
Infi-90 Node status problem
Dear Anthony We win and resolve the problem in opportunity of plant outage i replaced older...
Dear Anthony Unlucky i have no any spare slot in the PCU while we have redundant NIS/NPM..one...
Dear Mr. Anthony Thanks a lot for your guidance..yes it is true we have very old power supplies...
from the Instrumentation and Control department...Vibromter Absolute vibration calibration
Vibrometer UVC 752 and PLD 772 calibration
from the Instrumentation and Control department...DCS Infi-90 NIS module
Infi90 DCS NIS relay transistor
from the I&C department...DCS Cards PM
Standard Preventive maintenance procedure of DCS Cards
from the Energy Management department...Gas Pressure variation
How to manage the gas pressure variation during winter season
from the Instrumentation department...ABB AMD 230 Absolute Pressure TX
ABB AMD 230 Pressure TX configure
from the Instrumentation department...Steam turbine ABB Ansaldo Turning gear
How to run the turning gear when the related process control panel need to be power off.
Dear CSA thanks for your advise..basically i want power off the PCU when machine is on turning...
from the Instrumentation department...Informaiton about Control valve
Any body knows about these control valves
from the I&C department...GT(V-94.2) Trips during starup on F.O
GT V-94.2 fuel oil startup problem
> Sure you can go for Fuel oil Hot start upto 240c OTC. For that you should study the start up...
Dear Sir, Thank you very much for reply. Can u plz Explain the lower light of speed. have u...
from the Instrumentation and control department...About Fox boro dcs
Thoughts/experiences with foxboro dcs
i have worked with Foxboro DCS IA-6.4 with UNIX. it was my best experience and this system is very...
from the INSTRUMENT department...GT Seimens V-94.2 tripping on flame failure
GT V-94.2 trips in step 15 when it is on fuel oil
dear Sir Answers given below: we are using infi-90 by bailey control wile we tried the...
Select Page: 1
The moon may be smaller than Earth, but it's further away.