Search results

Search everything Search threads Search blogs
You may enter multiple names here.
  1. N

    Load control by Droop vs isochronous in island mode

    Helllo,you can ask the resident engineer to see what is the problem in this case.I would suggest you to se the functional description document to understand what is going to better see the implications.Also are you trying to start up the gas turbine in droop or isochronous,because,unless a...
  2. N

    Mark VI UCVE dead?

    yes,I formatted the flash drive and installed the system again,this time it worked well
  3. N

    Can't ping Bentley Nevada although the values are visible!

    we left itas it was,we were not able to ping it though
  4. N

    Mark VI not going online

    Hello WTF,I am doing an HMI Upgrade,just substituting the software of the controllers and not the controller itself in a plant in Germany Firstly I searche the forum to see if anyone else had had this problems with the Mark VI systems and apparently a lot of people had had problems. I saw a...
  5. N

    Mark VI not going online

    Hello WTF,I am doing an HMI Upgrade,just substituting the software of the controllers and not the controller itself in a plant in Germany Firstly I searche the forum to see if anyone else had had this problems with the Mark VI systems and apparently a lot of people had had problems. I saw a...
  6. N

    Mark VI not going online

    I am doing an upgrade of a Multiunit.There are 4 units in the plant,but 3 gas turbines have Mark VIe system to operate them,one has Mark VI operating it.I made it so I could put the Mark VI online but I could not see the alarms in the Workstation even although everything was configured...
  7. N

    Mark VI UCVE dead?

    hello,I am facing the same problem,did you guys resolve it?
  8. N

    Alarm list not showing on HMI

    I am experiencing the same problem at my plant,did you resolve it?
  9. N

    Why cant I see alarms?

    I suspect this is the problem as you say,but I dont know how to resolve it
  10. N

    Mark Vle controller problem

    Have you tried booting the controller memory using a USB 2.0 flash drive? If you go to device then download to USB it is pretty straightforward
  11. N

    Why cant I see alarms?

    So I am trying to do an upgrade for a multiunit plant.There are 4 gas turbines,but one of them has the Mark VI controller,the three other ones have the Mark VIe controller.Unfortunately I cannot see the alarms of the Mark VI ,but I can startup and shutdown the gas turbine.In the alarmID I cannot...
  12. N

    Synchonization of UCVE in MarkVI

    Hello,thanks for the details,i have the same problem.What will happen if I try to reboot the controller again,in the sense of using a flash drive to make it start again
  13. N

    Client's device sees freezed values.Why are not the values updating?

    thanks,it was Modbus RTU,the problem was that the Raw Min,Raw Max,and Eng Min and Eng Max values were not defined well in the toolboxST
  14. N

    Client's device sees freezed values.Why are not the values updating?

    Hello,where do I see what type of Modbus do I have?
  15. N

    Client's device sees freezed values.Why are not the values updating?

    We are trying to give the value of some variables to a client's Modbus Master using a Communication Gateway and let's call this Communication Gateway A.We had put the digital variables at the holding registers and we could not see them.I put them at the Input Registers and now the client could...
  16. N

    Why dont HMIs communicate with each other?

    Yes,every firewall is off,it does not help it.Microsoft has dropped thr bag with this one,it makes things very difficult
  17. N

    Why dont HMIs communicate with each other?

    I can ping them,also I can control them in remote desktop connection.If I remap them,only from HMI I get the error 0x80070035,which basically says that it cant find the specified address.I see that this is a common problem with Windows 10
  18. N

    Why dont HMIs communicate with each other?

    So i did make some changes today,basically I ran the the run,typed services.msc and changed there a) Computer Browser (Browser) b. Function Discovery Provider Host (FDPHost) c. Function Discovery Resource Publication (FDResPub) d. Network Connections (NetMan) e. UPnP Device Host (UPnPHost)...
  19. N

    Can't ping Bentley Nevada although the values are visible!

    So they are on the EGD network.They are on the 101 network.MARK VI gets the data from them through an ethernet connection,from Bently Nevada to the MARK VI,and I can see the data in the HMI,I just cannot ping the Bently Nevada
  20. N

    Can't ping Bentley Nevada although the values are visible!

    Hello,also the old ones were Cisco,albeit a newer switch model.No the new VLANs have changed,the number of the ports is not the same.I can ping from the HMIs the Mark VI but I cant ping the Bentley Nevada or RX3i,but i can see their values on the HMI!So the Bentley Nevada is really connected I...
Top