Recent content by Dayo

Search Forums New Posts
  1. D

    G. E Exhaust Thermocouple with P/N 328A8483P001 change to P/N 302A4010P002

    Thank you so much, WTF. Your response is highly appreciated.
  2. D

    G. E Exhaust Thermocouple with P/N 328A8483P001 change to P/N 302A4010P002

    Dear CSA, MKVi guy and other guru of this platform, I kindly await your response. Thank you.
  3. D

    G. E Exhaust Thermocouple with P/N 328A8483P001 change to P/N 302A4010P002

    Dear bidrohini, I sincerely appreciate your quick response. This is the situation. We planned a Major Maintenance on frame 6B Gas Turbine and requested for Exhaust Thermocouples with P/N 328A8483P001 which is what we are used to, but our Spare part Supplier, supplied Ttxd with...
  4. D

    G. E Exhaust Thermocouple with P/N 328A8483P001 change to P/N 302A4010P002

    Good day dear colleagues. I sincerely need your assistance and Clarification (CSA and other great mentor). I want to find out if G.E. changed the Part Number of Frame 6B Exhaust Thermocouple (ttxd) from 328A8483P001 to 302A4010P002. I eagerly await your response. Kind regards, Dayo
  5. D

    Actual IGV angle not same as both reference and feedback.

    The problem was therefore rectified.
  6. D

    Actual IGV angle not same as both reference and feedback.

    The washer and the bolt were replaced with good ones and were properly tightened to the IGV pointer
  7. D

    Actual IGV angle not same as both reference and feedback.

    MIKEVI You are right. The problem was actually the IGV position indicator. It was discovered that the IGV lock pin was not in it position and both the washer and bolt that were holding the pointer in position were also worn out which probably led to a shift in igv position indicator (the...
  8. D

    Actual IGV angle not same as both reference and feedback.

    MarkVI I do appreciate, """In your case here I ask who was doing the measuring?--- Have they done this before? ----If not who did it before and did they know what they were doing?""" The IGV was commissioned 16years ago and has been operating fine (though we have rectified so many faults...
  9. D

    Actual IGV angle not same as both reference and feedback.

    Dear everyone, Our Gas Turbine, frame 6b with Mark VI control was shutdown normally 2 days ago. Mechanical requested we open the IGV to carry out maintenance work. The IGV was opened and was okay, but when we closed it after their inspection, the physical angle was more than the reference...
  10. D

    Ratcheting Problem

    Dear CSA, Sorry for given the feedback this late. What was done to solve the ratcheting problem was the ratcheting pump which was checked initially. This time the ratcheting pump was serviced and placed back ( because we could not get a new one as at that time). Our Gas Turbine is back on...
  11. D

    Ratcheting Problem

    I sincerely appreciate your quick response. We will check and re-check all you have mentioned and feedback will be given. Thank you.
  12. D

    Ratcheting Problem

    Dear CSA, I have eagerly been waiting for your response. Work done Yesterday, Confirming the status of Ratchet pump( PH3) - Ratchet pump of the defective Gas Turbine ( GT2) was installed on a working GT1. GT1 was placed on Cooldown, the ratchet mechanism worked well, which confirmed that...
  13. D

    Ratcheting Problem

    Dear CSA, Good day CSA and other great mentors of this group. We have applied lots of information explained on this forum on this same topic but no result yet. About four weeks back, our Gas Turbine Frame 6B (ISO - 42MW) with MkVl control was shutdown normally, but failed to ratchet. The...
  14. D

    Can IS200TREGHIBDB be replaced with IS200TREGHIBDC?

    Good day CSA. This is the J2 picture you requested for. So it means that when installing the BDC, the J2 connector will be rotated by 180degrees. Thank you so much.
  15. D

    Can IS200TREGHIBDB be replaced with IS200TREGHIBDC?

    As I mentioned earlier, the loss of power supply happened some months back when installing the H1BDC on the panel (the J2 picture I sent and that might have affected the #3 socket you noticed in the receptacle). We actually got another spare of H1BDB from store house which we placed and the...
See more
Top