Recent content by mhwest

Well, it makes your forum almost useless.

From within a TMOS graphic you would use something like this: ADDMENUITEM 20010201 "GT#3 Rungs" 100 "rungdisplay.exe '@settings_scc3.txt /xpos=13 /ypos=40 /center=true /monitor=0 /unit=3 /user=%user%'" ",1,2,22,23,24," I have never tried to setup a shortcut to open...

>You are right CSA. Earlier we replaced the card with >another one, but we did not sure it was new/good/faulty. So >we replaced with brand new one, then everything came normal. This thread hits home - We have had quite a few, 5-6, events over the past 2 years where we replaced a card and...

CSA, I think you must have misunderstood something along the way. I don't believe you will find any post from me that indicates I am aware of anyone in the industry who has develeoped a non-GE interface to MK-6e which can get alarms and events from a MK-6e. The orginal post that began...

RRA: Your question is very specific. You asked about communication between the DeltaV and MK-6e. We have six MK-6e 7FA combustion turbines (Migrated from MK-5) - they are in isolated 1x1 combined cycle blocks. For all 6 of these blocks we are using redundant TCP Modbus directly between...

LCPBH1_0_F should originate from a FDIA block. Refer to GEH-6810 for some information on the logic. The latest version I have seen is rev B. In some systems you can drill down into the FDIA block and study how it works if you have time and patience. But, I believe that in many systems GE...

Shortly after posting my previous, I found TIL-1524 issued in 2005 which offers the change as an upgrade. Also, the TTXSPV6_1 block has a HIGHSEL parameter that defaults to false, which if true uses the highest T/C in the spread calc, the 2nd highest if false. For ToolBox4 with the TTXSPV4...

This thread caught my attention and I looked at 2 different generations of MK-6e 7FA controllers in our system. I was surprised to find that for our MK-6e systems Spread1 is calculated using the 2nd highest and lowest exhaust T/C. Likewise, spd2 and 3 use the 2nd highest. This is true for a...

I have a procedure I wrote for UCSBH4A. I will send you if you provide a contact email address. I do not see a way to upload to this forum's website.

> On your comment on an OSM. Not just sure what you mean by > OSM. Is that an Historian? OSM=> On site Monitor, a PC/server GE puts at the site and connects to the arcnet to feed data to the GE monitoring and diagnostic center when either a unit is still within the warrantee period or there...

> With that understanding, how could the modbus crash > part of <C>? It would seem to be isolated from <C> by the > <I> computer. A problem might stop the modbus from working > or maybe lock up the <I>, but I don't understand how it > could cause problems with the <C> core. Love to either...

> file below. And the ALE111 card specification is 10BASE-T. I speed 100 This is almost trivial, but I have worked long hours many times because something trivial when over my head. Change the "speed 100" to "speed 10" in the 2960 switch configuration, or remove the command and let it...

CSA, I have seen excessive igniter insertion depth cause re-ignition of the primary shortly after transfer a number of times over the years. It's a glow plug.

Several companies ahve products that would suit your needs. Both CSE engineering and Control system technolgies have HMI products for the MK-4 that support modbus. I believe both have products that can support modbus directly to the panel. PRISM systems has an OPC server that we are using...