Search results

Search everything Search threads Search blogs
You may enter multiple names here.
  1. ControlsGuy25

    exhust temprature

    We still need consistent and gathering datas like it has been asked on previous posts.. I know you understand that we can support from here with reliable service ...
  2. ControlsGuy25

    Cannot read Triconex (Tricon) aliased addresses

    Any error message ...
  3. ControlsGuy25

    limitation for cards in every node ABB AC900F

    Hi I knew that you were looking for something else was just a begining I have seen a manual ( One got to Pay online on SCRIBD to get it) It can highlight the points that you looking for ... Here is the link...
  4. ControlsGuy25

    limitation for cards in every node ABB AC900F

  5. ControlsGuy25

    limitation for cards in every node ABB AC900F

    10 I/O s MODULE PER CONTROLLER
  6. ControlsGuy25

    limitation for cards in every node ABB AC900F

    https://mcaps-inc.com/abb-dcs-systems/abb-freelance/acf900f-controllers/ac900f-central-processing-unit-cpu.html
  7. ControlsGuy25

    limitation for cards in every node ABB AC900F

    Hi dear @mehdiAnsari ABB ACS900F can support up to 1500 I/Os according to OEM manual I will try to find something about maximum nber of cards in each /every nodes..
  8. ControlsGuy25

    exhust temprature

    Ok We would need also some trends about datas related to the unit like exhaust spread temp.. Load FSR ..speed..and other controls constants
  9. ControlsGuy25

    exhust temprature

    Hi @abdooo99 We will need some datas like frame unit OEM Also if some trends are available , you can share here How do you operate these units Base load /Peak load???
  10. ControlsGuy25

    Ship Generators in Parallel Problem

    Good to hear that you find the origin of this issue!
  11. ControlsGuy25

    Ship Generators in Parallel Problem

    Selector swithes are on position ON ...
  12. ControlsGuy25

    Mitsubishi Servo System encoder error [A16]

    Is that similar that this case : https://www.kwoco-plc.com/mitsubishi-servo-display-al16/ also you better provide References Serial number for these devices for better support from here
  13. ControlsGuy25

    Turbine trips after grid circuit breaker open

    Looks like provided trends and datas are not enough to solve the issue as we dont know what happened to the "grid/line cirucit breaker 52 L at occurence" to get tripped * We do not know if it is kind of load rejection /shedding or other event can be a electrical fault ...
  14. ControlsGuy25

    Tatsuno Fuel Dispenser Communication to PC

    Hi Controlee Indeed i got all the mentionned OEM protocol and wiring diagram schemes Will share them asap Regards, @ControlsGuy25
  15. ControlsGuy25

    Ship Generators in Parallel Problem

    Looks like original poster isn't showing cooperativity I dont why come here and post and connect then leave thread without answer Thats not professional at all!
  16. ControlsGuy25

    Ship Generators in Parallel Problem

    Just for information Is that normal that space heater is ON and lamp showing OFF
  17. ControlsGuy25

    Ship Generators in Parallel Problem

    Sir we would need to check load consumer list Can you tell us about reactive power behaviour? Single line diagram Is there kind of PMS (Power management system module) Is there kind of cross-current or Reactive power compensation scheme on these units?
  18. ControlsGuy25

    Controllogix communications via ethernet to ABB VFD drive

    Thank you for your attention and reply I will contact as I do have some experiences on ABB & Rockwell & ABB VFD s Regards, @ControlsGuy25
  19. ControlsGuy25

    Controllogix communications via ethernet to ABB VFD drive

    Where is job /plant located ? We may be able to support
  20. ControlsGuy25

    Turbine trips after grid circuit breaker open

    Root cause can be multiple .. It can be a load rejection.. Load shedding.. What is kind of turbine and manufacturer What is control system installed on this unit. ' We would need alarm list or trends to provide support to solve this issue in the future
Top