Search results

Radar would work fine.

To me it looks like a skin type thermocouple.

My first suggestion would be to look for coriolis mass flow meter the straight tube type. They are better in place where installation space is a contraint. But then again if there are lot of vibrations etc. then best is to go with any flowmeter which has no moving parts at all like the portable...

If your measuring span is within 4m then the transmitter sent to you will work else you have to go for another one with a higher rope length according to the span being measured. Another thing just curious to know, did not the supplier in the specification sheet before procurement of the...

There has to be a ground occuring on the negative side as it is lowered by 9Vdc (55vdc-9vdc=46vdc). Similarly you see the positive side with respect to earth is equally floated up to 62Vdc because 9vdc(gnd) plus 55vdc(+ve side) equals to 62vdc. Check the negative bus side and the cables. Also if...

I hope the DD files are correctly installed and with the latest revision.

DVC 2000 is used in valves which are smaller in size and with less travel like the Baumann valves. DVC 6200 on the other hand is used in larger size valves. The travel specifications for the same, I don't remember correctly but you can read it from the individual manual of the positioners. And...

Of the systems that I have worked with, drum level is cascade control with feedforward trim and combustion control is ratio+ cascade + feedforward trim but then again it all depends upon the consultant and to the OEM about how they want to implement it. But generally it is a mix of different...

Were all your valve working fine in the beginning? Generally an arrangement for venting is provided to protect from overpressure..if your valve is not moving at all..or if there is too much backpressure then this happens.

In my experience the most nuisance happens when RTD's are directly connected to RTD Card by triad cable and the cable has a bad installation practice.. Best is to keep the triad cable short and install a Tx in between and take 4-20mA instead to an AI card. But with a lot of RTD connections in...

Looking at the attached PDF, you might want to try changing the line frequency from automatic to whatever you are using...50Hz or 60 Hz. I believe there should be a setting for that. Also check if there is a possibility to increase the field frequency from the settings. From the PDF it shows...

What is the MOC of your tank?? And at what frequency is the transmitter working?? Also do an echo curve mapping and check if it solves the problem. Another thing I want to say is that for a 1.9m tank, your range for a non contact radar tx can never be 1.9m. Any Tx employing the time of flight...

Radar is a form of electromagnetic radiation and utilizes the radio or microwave frequencies and the time of flight principle for measurement. For radar, one of the most important criteria for choosing the technology is the dielectric constant of the medium that it is traveling through and as...

I'm sorry...my typing mistake....It is 3 o clock and 9 o clock...!!! 12 o clock is avoided as the liquid might have air bubbles inside entrapped and air bubbles would flow through the upper surface of the pipe which would lead to erroneous flow readings.Also half pipe flow is another factor why...

I'm not sure about what is the fault that you are talking about is happening to your transmitter...Is there a pressure spike or is it one side is 145 bar, while on the other side it is 1 bar...???? But the one side 145barg while on the other 1 barg, this is a phenomenon that occurs during cold...

First It is because each type of thermocouple generates different millivolts according to its hot junction(sensing point)temperature and the cold junction(reference point) temperature. Or in other words the sensitivity of each thermocouple type is different from other type. The mV/degree...

Were any trip commands generated by the turbine's control system while the water was getting inducted into the turbine??

To answer your first question...The best place is generally decided depending on the pipeline and the liquid medium For clean liquid two traverse installations are the best, with sensors mounted at 3'o clock or at 6'o clock position as this kind if installations provide better accuracy... But if...

You said that with increasing current the actuator does not move...I think this might be a case where the controller's output is not able to drive the load(actuator in your case)... Is the same controller driving similar other actuators?? Are they working properly??? If they are working...

We have watchdog trip relays of carlo gavazzi...top notch performance and a bit pricey...finding proper suppliers are a bit of a heck though!