Search results

It is my impression from discussions with DCS operators that Honeywell periodically releases authorized updates as part of their paid/subscription services after having tested the updates . If you don't have paid service for your system then the testing is your responsibility.

No direct experience with "low flow cutoff in Krohne systems" but I'll make several observations The graphic appears to be an HMI batch screen. Are you saying that this a Krohne software/HMI product? If so, which one? There are any number of stand-alone batch controllers and who knows how...

The value is a 32 bit floating point (FP) value consisting of four 8 bit bytes. There are four IEEE754 word/byte order formats to produce a 32 bit FP value, as shown in the graphic below from vendor documentation. The terminology varies by vendor, some call it "endianness". Out of the...

In the US, the hard hats seem to have a molded 'slot' on the each side. There are a number of LED flashlights that are designed to fit into the slot on the side of the hardhat. There are hundreds of models with straps that fit around a hard hat. There are even lamps rated for hazardous areas...

At this link https://control.com/textbook/foundation-fieldbus-instrumentation/h1-ff-data-link-layer/ there's some discussion of comm management, albeit without any sample packets, just descriptive commentary. FF is not like the Modbus protocol where the standards are public and there are...

AGA 3.1 Orifice Metering of Natural Gas https://law.resource.org/pub/us/cfr/ibr/001/aga.3.1.1990.pdf

The description at the top right of the drawing, 2nd arrow down, "Type E Terminal head" is a fairly good indication that the element is a Type E.

A voltage measurement is inherently a differential measurement, the difference in potential between point A and point B, red probe (+) with respect to the black (COM) probe. It's easier to make voltage measurements 'above or below' ground with a battery powered, plastic-cased voltmeter because...

Yes, a current loop signal is 'the same' throughout the loop, at the source and at the destination. Voltage signals 'drop' voltage over distance.

a sketch would help. Draw it with dimensions and take a photo of your sketch with your cell phone.

In English, word order is important and if you'd written adalah flow meter (instead of Flow meter adalah) I would have proposed: A) Another flow meter vendor by the corporate name Adalah B) After residing in the Commonwealth of Massachusetts for 7 years, I could easily propose that a New...

You really need the E&H Promass 80 configuration manual: https://tinyurl.com/2ubt7xkm The Quick Setup Group navigation menu is shown on page 14. The System Units group is first, followed by the Measuring Mode Group. E&H calls the URV the "Value 20 mA", as shown in the Measuring Mode group...

An RTD input circuit does not 'send Ohms'. Most RTD analog inputs drive about 1mA of constant current through the RTD resistance and then read the voltage drop. A 150 Ohm resistance generates only 150mV of IR drop, a fairly low level signal to read over hundreds of meters of lead wire which...

It occurs to me that the situation is a number of flowmeters are being commissioned. The spreadsheet has a column for each point that has a 'maximum' expected flow rate. The flow meter has a 4-20mA output which is to be configured for 125% of that maximum flow rate so that in case the...

I'm lost. I've done lots of flow meters but I don't know what "max flow over 120%" means. Are you measuring gas or liquid? What is communication output of the flow meter? A digital protocol or 4-20mA? The typical flow restriction on a coriolis meter is when the pressure drop gets too high...

This site illustrates differences between tapered NPT and BSPT threading and describes the straight thread BSPP. https://www.geminivalve.com/bsp-thread-vs-npt-fitting/ What the majority of tapered threaded fittings are depends on where in the world you are.

a signal conditioner, ±5V input with a relay output, like the one here: https://api-usa.com/pdf/api/api1080g-1090g.pdf

You should be communicating with the manufacturer of the brand and model that you've tried, explaining how the valves you purchased don't function properly and inquiring as which models the vendor offers that can solve your problem.

3-4 years ago, I would turn on my laptop when I got to work and go get a cup of coffee in the break room because it was a full 5 minutes before Windows desktop appeared and the HDD LED went from solid on to occasional blinking. The IT guy asked me if I wanted to change over to a SSD drive...

Link