Search results

Search everything Search threads Search blogs
You may enter multiple names here.
  1. grajesh

    Thermocouple Cable for Signal

    Thank you CSA, Completey agreed with you. Yes we too not fully ready to replace the cable with T/C's extension, just studying the mertis and demerits if any emergency occurs. Thanks again. Take care G.rajesh
  2. grajesh

    Mark VI and Mark VIe

    very useful feedback, thanks CSA.
  3. grajesh

    Thermocouple Cable for Signal

    Hello everyone, Can we use the thermocouple cable for signal about 15 meter distance? We understood thermocouple cable characteristics are different than normal copper wire. We are planning to connect servo valves, LVDT's, few pressure transmitters signal (4-20 mA) to thermocouple...
  4. grajesh

    Flame Detector Cable

    Few days back one of our Frame-9E machine tripped on loss of flame. Before trip, flame # 3 & 4 were reading 0 count. We have noticed flame detector # 4 cable damaged, it was replaced along with new flame detector. TCEA card replaced as 330 V from Mark V was missing. Now unit is running normal...
  5. grajesh

    Mark V ribbon cables

    Thanks you for the detailed list. Take care G.Rajesh
  6. grajesh

    GE MARK5 CONTROL SYSTEM

    GREAT feedback as usual by CSA. Take care G.Rajesh
  7. grajesh

    Exhaust High Spread

    Dears, We had an issues with exhaust temperature high spread for one of our Fr-9E machines. Unit was running with normal spread around 12 deg.C with gas fuel operation. after unit transferred to liquid fuel due to gas low, temperature spread was increased to 24 deg.C. when unit was...
  8. grajesh

    Two Frame-V GTGs Generating Same Power, But with Different Fuel Flows

    Very useful information to give feedback by Mr. CSA. Take care G.Rajesh
  9. grajesh

    GE Exhaust Spread Trip Logic

    Yes, agreed with CSA forcing logic should be avoid as much as possible and before forcing anything we have to take care all safety issues behind. Take care G.Rajesh
  10. grajesh

    Loss of Communication Between HMI and MARK V

    Probably there might be issues with ArcNet card. As advised check the nodes by ARCWHO. take care G.Rajesh
  11. grajesh

    Gas Turbine Startup Problem

    Happy to knew your problem is solved. But if IGV was operating well during manual stroke and strange why didn't operate while starting the machine? Just to learn, what alarm caused to trip the machine? Take care G.Rajesh
  12. grajesh

    GE-9E Dual Fuel Gas Turbine Turning Gear Run time

    Well explained by CSA Take care G.Rajesh
  13. grajesh

    Generator and Capacitor Bank

    Some useful information. Take care G.Rajesh
  14. grajesh

    Gas Turbine control - Hardware Part Trip of L4

    Very happy to see the detailed discussion. Go ahead for great success. Take care G. Rajesh
  15. grajesh

    Mark V A6 state

    Thanks Bob for your feedback. No we couldn't locate the card as when it was at A6 and found cable short circuit, processor kept down. Once problem rectified and powered up it reached A7 without an issue. Take care G.Rajesh
  16. grajesh

    Mark V A6 state

    Additional to the above, ribbon cables between CTBA and TCCA has been removed, cleaned and fixed back. Take care G.Rajesh
  17. grajesh

    Mark V A6 state

    Yes, for us to it's strange behavior but no other clue, how it resolved. Take care G.Rajesh
  18. grajesh

    Mark V A6 state

    Thank you all for your as usual supports and thanks CSA for your welcome. We found some cable short circuit in the field pressure transmitter, we down the Mark V panel and short circuit rectified. We have relocated the damaged input to the good one. <C> reached A7. We are not sure, field...
  19. grajesh

    Mark V A6 state

    Thank you for your feedback. We have tried to revert back the changes but still at A6. Take care G.Rajesh
  20. grajesh

    Mark V A6 state

    Dears, Since one pressure transmitter contact at <C> damaged. it relocated to good one and IO.ASS and IOCFG has been modified. After done MarkV make, user file has been downloaded to <C>. But after that <C> not reaching A7, staying at A6 and showing IOCFG failed. Please advise us Thank...
Top