Search results

Hi Gaurav, Thanks for your feedback! Any updates on the evolution on this issue... I will have a better read on the thread and then will come back for comments.. Regards, James

Hi plz have a read on that article... https://www.power-eng.com/coal/hrsgs-must-be-designed-for-cycling/#gref

Hi Have a search on this forum threads on that subject.. It Looks like you need to ask for CMS "combustion monitoring system"... Do you have a discussion with your GE representative... Like CPM/engineering... They use to support customer by remote office engineering.. James

What kind of utility/facility is it? Which mode do you see there is load swingings in the PF Volt/Var control modes?? Can we know more on OEM Steam turbine /generator /AVR and associated grid .. Is there kind of PSS need to be tuned and activated during transients modes/times ... Many...

The answers are clearly given in the Rung display modes of the Markiv CRT in the OEM manual! It is about Fn functions & Cursor selections used on CRT & Opeartor interface module to navigate and see which current signal status or dispaly the rung sequentially as per your rung ! I am sure that...

Hello All, What you mean by "Reset the setting " IS IT not better to restore parameters to original values ! I will post some more gatherings datas tomorrow by the way! You can/may use that function as it is written on OEM manual. Or maybe another solution is to re - set not reset the...

Hello You would have better to read the quick start up and setting /parameters configurations manual on such Device. Have a search on that manual on the web and read it carefully, it is described how to do such settings/parameters configurations get correct! Depending on the application of...

Hi all! I strongly advise you to get a read on thi sthread: https://control.com/forums/threads/external-mismatch-alarm-in-triconex-ao-card.47374/ Hope this can highlight some points ! James

Hello All It is called a CONTACT variation : From Mark IV&V user Manual it is saying that One logic signal can be used to multiple contacts. Have a search on the Right Technical manual From OEM it is always a good thing to do ! Thanks for sharing such Post We are here to share and learn...

Hello all, You stated as per manual : The manual says that this is an indication of failed ID chip on connector J2/J5/J6 or cable problem. I read on the GEH6421 Vol2 it saying that These "code Fault 18 is RELATED J3 CONNECTOR ..." Can you tell us where do you see taht it is for J2 .... I...

You can use Function blocks dedicated for example like "Compare block " as you asking about it You will find it in th elibrary of Siemens plc... Also have a search on the wide web you surely will find response to your questions By the way we are here in case you need some support.. ControlsGuy25

Hello there, A sketch/schematic/drawing would be greatly appreciated...

Hello Sabasnm, Thanks for the feedback! Yes i can share the file sure it describing also galvanic protection/isolation ... It contains all necessary drawings for good operation with unit conditioner also.. Regards, ControlsGuy25.

Hello Makster, I can suggest you to check with Thomassen BV netherlands as they working with GT H25 .... Also you can contact this company taht i add the web link here : https://www.mfsupport.com/ Check also with this company in Germany : https://supply.parts/request/view?id=314883 They are...

Hello Can you tell us plz the system that this sensor is due to worked with... Did you right correctly the OEM manuals? I had a read on them, and the most of the questions taht you listed got answers in these documents.. I can share with you one document if you dont have it as it is too bog...

What did you find on the OEM technial manual about that "VFD multiple units sync ...." They are bunch of documents & videos on the WEB that can be useful ! Try to have a good read first on that documents.. And tell us more on the system workd on : -What communication protocol is used for...

Dear David Meng, You are welcome! Glad to see that this manual is useful! Do not hesitate to share what you did on this issue ! Best Regards, Controls guy25

Okay good... It is sometimes better to proceed by this way.... Thanks for your feedback.

Hello Makster, Looks like you got serious problem at site! Can you answer to the following questions then we will try to support you: Can you provide part numbers /serials number with OEM specifications ... I can have a check with my partner to see, if they got such parts available and also...

Hi Is there any action done prior to get such "message"<< Did there were any upgrade on any equipment related to this SCADA ... Looks like you will need to troubleshoot by your own technical manuals that you got as there is some informations on MYSQL/SQL server if it the case... Well lets...