Search results

Search everything Search threads Search blogs
You may enter multiple names here.
  1. ControlsGuy25

    9FA Gas Turbine Filtre house and H2 seal oil

    So you can try to reply to my questions about site configuration /history then i can try to support .. For sure you better replace that CF or at least remove and clean them
  2. ControlsGuy25

    9FA Gas Turbine Filtre house and H2 seal oil

    Maybe you can try another OEM for replacing these CF..
  3. ControlsGuy25

    9FA Gas Turbine Filtre house and H2 seal oil

    Hello Who is OEM cleaning filter /pulse cleaning system manufacturer.. When this plant as been commissioned ..when this problem raised..."since begining ."or other .. I would try to contact OEM manufacturer or GEEPE In Belfort...They better placed to answer on kind site conditions...
  4. ControlsGuy25

    A question about IGV and 2nd stage nozzles fail position and opening angle?

    Can you share this manual here...
  5. ControlsGuy25

    mark v idos

    That DIP switch shown on the screenshot looks very used and old...are you sure about that device working properly see notes from OEM manual on that DIP SWITCH setting:
  6. ControlsGuy25

    A question about IGV and 2nd stage nozzles fail position and opening angle?

    Actually I found one good manual on the web, but need one to suscribe and pay for dowloading it....which is not a bad thing with kind of support from the document... https://fr.scribd.com/document/245177004/MS5001-PA-Complete-Maintenance-MANUAL
  7. ControlsGuy25

    mark v idos

    Hi Thanks for the feedback and inputs.. Did you ever try Arcwho line command instruction ...seems not as you should see arcnet nodes after entering such command..
  8. ControlsGuy25

    A question about IGV and 2nd stage nozzles fail position and opening angle?

    Hi Did you have a read on the right OEM technical manual ... I am sure that you can get those details on such document... James
  9. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

    Hi I provide se notes from OEM manual.. All is well described... In this document .. Now you saying that these Maths make you inconfortable.. I cannot go further as.. You need to describe the studied system.. By adding a schematic/sketch/drawing at least..
  10. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

    Oneye14 I posted the right and useful pages to inform original poster (lw3eov) thats OEM manual is well describing the need in this case.
  11. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

    You are welcome!
  12. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

  13. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

  14. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

  15. ControlsGuy25

    Help requested with Mitsubishi FX2N PLC for PID control

    Hello I got some notes from manual which is clearly describing how to programm and tune PID controller with that OEM PLC.. See following quotes from this manual ( maybe you dont look at the right Technical Manual..):
  16. ControlsGuy25

    mark v idos

    Which device is connected to other devices..... Arcnet card need configuration to be ok ...as per OEM manual...did you follow these instructions (see GEH 6126 )
  17. ControlsGuy25

    mark v idos

    Hi Did you try "Arcwho " line command ...if yes what it returned... You got to provide typology/Architecture of the mentionnned controls system..Then we can provide better support from here.. Any time! James
  18. ControlsGuy25

    Generator Syncing but trips on 32 relay when GV are opening and steam is plentiful

    When one post some questions. One can atte'd a reply.. You did not reply... To my questions... Good luck with your problem! I leave this.... Thread... Adios... What is in your mind.... Do not treat people like that.. Otherwise.. You will regret it...
  19. ControlsGuy25

    Gas Generator Fighting Each Other...

    I told you that, the load scheme was not implemented /tuned well.....!
  20. ControlsGuy25

    Generator Syncing but trips on 32 relay when GV are opening and steam is plentiful

    Can you tell us : Governor model Turbine type ( extraction, condensing..) What you mean by GV's.... Protection relay IED or analog ...type model..software settings.. .. Grid configuration.... Load sharing mode .... I can then try to support ... james
Top