Dear Mr/Mrs/Ms

I'm having a problem about sending data and receiving data with serial port using Visual C++. So if anyone would like to help me? i'm very pleased for your concern.

 

Hi,

I am not sure what APIs you are using to communicate. To do serial i/o on windows, you cannot use the inport/outport calls. These will not work on winNT and up. These however will work on Win 95/98.

You will have to be more specific on the kinds of problems you are having and the device you are trying to interface with for anyone to help.

Nevertheless, many a times, its a problem of setting the correct baud rate, parity, data bits, stop bits and handshake that can lead to incorrect behaviour. Are you sure you have set all these correctly in your program. These must match the device.

Secondly, you must know the format of what to send and receive from the device - the PROTOCOL that the device uses. Do you have that.

Lastly, are you sure you have the correct serial cable for the device. Theres a couple of ways a serial cable can be designed - I hope you have the correct cable setup.

For more help - you may contact me directly at [email protected]

regards
- Punita

 

Hi!
I am looking for some rs232 data transfer software samples written in visual basic.Could you help me?...
e-mail: [email protected]

 

u 1 2 have the source code for sending and receiveing thru serial port??
what version of window u using??
what type of data u 1 2 sent and receive??
can give more details ??

 

Hello

Could you please help. I would like to interface to the serial port using Visual C++ 6.0. I want to it to work with the Windows 2000 operating system.

e-mail: [email protected]

Regards

Dhavan

 

Greetings.

Could you please write me if you can direct me to get a visual c++ program to access RS-232C port? I want to try sending a command to an instrument and receive data from it for further processing the data. I am using Visual C++ 6.0 running on MS Windows 2000. Please write me to the following address:

[email protected]

Thank you for your consideration.

best regards
R.Bala

 

i also have to these program like VC++ connecting RS232 could you send me some simple example??

[email protected]

 

Hello,

I am also search of Rs232 program in vc++, in case u have got any reply for any one, please send a copy of it.

Email:
[email protected]
[email protected]

 

Hello do any one have the code for visual c++ program to access RS-232C port? I am also trying to sending a command to an instrument and receive data from it for further processing the data. I am using Visual C++ 6.0 running on MS Windows 98. Please write me to the following address

[email protected]

bye
best regards
deepthi

 

You got something about what you are asking, please send me a copy of it. Thanks!!!

 

Hi all,

I am also writing GUI Application using Visual C++. Can anyone tell me if I should use Opencom(), ReadCom() or something else to access RS-232? Please send me to the following email address:
[email protected]

Best Regards,
Ben

 

Hi all,

I am also writing serial port communication program to access RS-232? Can anyone send me a sample program? Please send me to the following email address:
[email protected]

Best Regards,
Yildiz

 

Hi all,

I am doing the same. Please send me a sample program to the following email address:
[email protected]

Thanks.

 

Did anyone ever get a GUI working that controls the serial port?

 

i have VC++.net... and i don't know how to connect a DAC card that i design with a microcontroler... using VC++.net

Thank you.

 

Hello,

I am searching for RS232 program in Visual C++ v6 as well, please send a copy of any sample code if possible.

Email:
[email protected]

 

I am also search of Rs232 program in vc++, in case u have got any reply for any one, please send a copy of it.

[email protected]

 

I need to acquire data from RS232 which connected to a GSM modem. right now I'm using windows hyper terminal but I want to use the Visual C++ 6.0 instead. so can any one just give me a hint where to start?

 

hello

i need a sample code to send commands through rs232 port and receive back. these commands are sent to gyroscope. please send me. i desparetely need it.

 

I am also searching for Rs232 program in vc++6, I don't know how to start write. So, I wanna study about comunicating with RS232 example programs in VC++6. If you have any example of RS232 VC porgram, please send a copy of it.

[email protected]
[email protected]