Search results

There used to be webinars GE used to arrange. Check with them. Not sure either still they offer their learning center courses.

Strongly recommend to get in touch with the OEM. They have a permanent fix for this issue in the form a software patch. Their patch numbering scheme are very confusing to follow.

Please reinitialize the controller from an USB 2.0, 4GB or 8 GB pen drive, following the steps recommended in GEH-6700 rev AY page 572 OR section 7.4.1.3 Configure and Transfer IP Address to UCSB/UCSC/UCSE Controller (OR) if available may refer to the retired document GEH-6703 (Rev Q or higher...

If you have Hard disk image configured for daily backup, try restoring to older good known dates. Else uninstall the Control Suite and reinstall might help. But before you do anything messy, take a backup and preserve it safely. Also if you have soft key license, then take a screen of all the...

Appears like you have lost the program memory. I would prefer resetting the controller from a 4GB USB 2.0 (NOT 3.0) pen drive, followed by program might help.

Appears like you have lost the program memory. I would prefer resetting the controller from a 4GB USB 2.0 (NOT 3.0) pen drive, followed by program might help.

Its a very vague request ! What make and model you are expecting, because each vendor has their own style of dumping the information & depending upon the level of debug info required the quantum can vary. Say for example if its cyber secured system and it has heavy DOS attack, a week of log will...

Initially I felt you might be missing license. But your all required services are running fine and online. Appears like the broken link is between your Mark 5 and WorkstationST. Ask the OEM or the upgrade provider to support on this.

I guess you are using a wrong operating system. Try it in recent windows. Also can you translate the error message to English please ?

I would prefer 1st to check the TCW file. Is it the "ACTUAL" / "ORIGINAL" / "CORRECT" for your system ? I know many would prefer a back up copies and make modifications (Example Backup of Backup of Backup XXX.TCW), when you go online with that, then it will not be equal. If your site uses CMS...

Hi PaCubo, The easiest way is to ask the OEM for the equation. If they don't have then you don't have much choice. The other round about method is to get both input and out measured at the highest precision possible (like using a 6.5 digit calibrated multi meter) for the entire full scale...

Is it a typo error ? The OEM's website is talking about Ex2100e which is their current offering. Can you attach the full brochure?

I came to know that, mailing to [email protected] (handled by the Ex-Nexus team) would handle these kind of legacy upgrades.

@ Robhoski Did you tried running the USB cable through a metal conduit ? I would prefer using a standard GI water Pipe perfectly grounded only on one end closer to the controller and leave the other end open and run your USB cable through it. Plasma cutters are known for inherent EMI/EMC when...

Glad to know, you could figure it out and address it! Since Mark VIe system doesn't have any back plane system there is no way to detect what is connect in the system ? Hence you have to "Teach" the controller to look for a Terminal Bard with that bar code, so that it can provide an IP address...

@WTF? I came to know that GE acquired again Nexus team (A part of BH group) They may help. @HRG Try reaching out to them at [email protected]

As WTF mentioned, its not an easy task. Would recommend to get in touch with the OEM and see if they have any solution. You did not mention what is the OS your site is using. Many old OS will not run properly in latest hardware due to device driver missing. Running in a VM, has its own...

Hi @WTF? I don’t know the full story. But in bits and pieces. Long back GE used to have PLC division as JV with Fanuc called GE Fanuc (2008), where they had Military & Aero as well, as a part of them, which later sold to ABC company (~2013/14). The remaining products were sold under the brand...

Hi WTF, If supplied by GE gas power or Emerson (Yes, you read it correctly!!), then it will use Proficy License Client, which you can usually find in start menu. If not in our HMI I see its located in this path. C:\Program Files (x86)\Proficy\Proficy Common\Proficy Common...