Latest CNC Technical Articles

Driving motors is one of the most fundamental automation tasks, but understanding and selecting the proper motor soft…

Driving motors is one of the most fundamental automation tasks, but understanding and selecting the proper motor soft starter for your application may require more investigation than you thought.

Many articles address the wiring and implementation of analog control signals, but where are they used, and what might…

Many articles address the wiring and implementation of analog control signals, but where are they used, and what might make them a better (or perhaps worse) decision than digital input/output devices?

Using the right motor for the right task is critical - but what happens if the motor is connected to the wrong supply? It…

Using the right motor for the right task is critical - but what happens if the motor is connected to the wrong supply? It is never recommended, but important to quickly understand symptoms of incorrect wiring.

Digital signals hold a prominent position due to their compatibility with computers. But what are digital signals, and…

Digital signals hold a prominent position due to their compatibility with computers. But what are digital signals, and what are some examples of the various devices used with digital inputs and outputs?

Single-phase motors are common in household and small industrial devices. They are a bit more complex than 3-phase…

Single-phase motors are common in household and small industrial devices. They are a bit more complex than 3-phase models, so it’s important to recognize failure modes and common symptoms.

Virtual networks can connect or isolate various local control networks through configuration of a managed switch. Why…

Virtual networks can connect or isolate various local control networks through configuration of a managed switch. Why would we use VLANs, and how can you segment a network switch to create a VLAN?

Ground wires reduce the risk of injury and damage from faulty equipment. Shops designing according to the UL 508A…

Ground wires reduce the risk of injury and damage from faulty equipment. Shops designing according to the UL 508A standard must understand how, when, and why to properly ground and bond circuits.

Structured Text (ST) is one of the common IEC programming languages that can be used in programming PLCs. Learn how to…

Structured Text (ST) is one of the common IEC programming languages that can be used in programming PLCs. Learn how to use structured text to write executable programs for MELSEC’s FX series PLC.

Compliance and compensator devices are used in processes where variation and uncertainty are prevalent. What sorts of…

Compliance and compensator devices are used in processes where variation and uncertainty are prevalent. What sorts of compliance devices are used, and what distinct advantages are held by each?

Rockwell Automation’s Micro800 series is the modern replacement for some older MicroLogix PLCs. Learn how to get…

Rockwell Automation’s Micro800 series is the modern replacement for some older MicroLogix PLCs. Learn how to get started with basic I/O, plus timers and counters, to build your own programs in a snap!

Force compensators and force compliance end effectors can expand the capabilities of traditional robotics to reach into…

Force compensators and force compliance end effectors can expand the capabilities of traditional robotics to reach into difficult processes, ranging from grinding and alignment to precision measurement.

Stepper motor control can be useful for motion applications. Learn the circuit connection and programming instructions…

Stepper motor control can be useful for motion applications. Learn the circuit connection and programming instructions for implementing stepper motor control using GX Works 2 on MELSEC FX-Series PLCs.

Three-phase motors are a backbone of the modern industrial control landscape. But plenty of applications still rely on…

Three-phase motors are a backbone of the modern industrial control landscape. But plenty of applications still rely on single-phase motors. Can these types of motors be reversed, and if so, how?

GX Simulator2 is one of MELSOFT’s essential tools for the simulation of programs in a virtual PLC and works with GX…

GX Simulator2 is one of MELSOFT’s essential tools for the simulation of programs in a virtual PLC and works with GX Works2. Learn how to virtually simulate and test your ladder programs.

Industrial robots are becoming safer and more economical by utilizing safety signals over Ethernet networks via CIP…

Industrial robots are becoming safer and more economical by utilizing safety signals over Ethernet networks via CIP safety technology.

An introduction to the various tag types used within one of the leading supervisory control and data acquisition (SCADA)…

An introduction to the various tag types used within one of the leading supervisory control and data acquisition (SCADA) software powering IIoT, HMI, and I4.0 applications: Ignition by Inductive Automation.

Temperature profiling is an effective tool to monitor thermal properties in process equipment. This article defines…

Temperature profiling is an effective tool to monitor thermal properties in process equipment. This article defines temperature profiling, discusses the process components, and describes the various benefits it offers.

Any kind of computer programming can be challenging to determine what aspects are truly unique versus what aspects should…

Any kind of computer programming can be challenging to determine what aspects are truly unique versus what aspects should be standardized across projects and platforms to streamline future development.

This article features an in-depth discussion of the various options for buttons and switches, including function, styles,…

This article features an in-depth discussion of the various options for buttons and switches, including function, styles, shapes, and illumination options for all kinds of control panel inputs.